Composite Privacy Kit - Woven Installation
- Up to 95% privacy
- Wind-resistant (does not flap)
- PVC-free composite designed for outdoor use (UV, frost, hail, rot-proof)
Privacy screening for rigid fence panels
Privacy kits for rigid fence panels: composite woven or straight installation, and PVC straight installation. Check compatibility requirements before ordering.
CompositePVCStraight installationWoven installation
This content is blocked
Embedded videos load only after you allow them. This third-party content may set cookies; allowing videos does not enable advertising trackers.
Was this video helpful?
Composite Privacy Kit - Woven Installation
Ultimate® Privacy Kit - Straight Installation
PVC Privacy Kit - Straight Installation
Our privacy screening solutions
Bestseller
Ultimate® Privacy Kit - Straight Installation
- Installation in under 5 minutes
- Tool-free installation thanks to factory pre-mounted inserts
- Ready-to-install carton
PVC Privacy Kit - Straight Installation
- High-quality PVC, anti-UV treated
- Quick installation in approx. 9 minutes, straight mounting without clips or tools
- Simple and intuitive system
Compare privacy screening kits
| Specification | Composite Privacy Kit - Woven Installation | Ultimate® Privacy Kit - Straight Installation | PVC Privacy Kit - Straight Installation |
|---|---|---|---|
| Kit mesh configuration — 45 meshes | 45 meshes | 45 meshes | 45 meshes |
| Kit mesh configuration — 50 meshes | 50 meshes | 50 meshes | Not applicable: this kit is not available in a 50-mesh configuration |
| Intended panel length | 2,50 m | 2,50 m | 2,50 m |
| Compatible inner mesh (between the wire's inside edges) | Not specified in the product sheet | Not specified in the product sheet | 50 or 55 mm |
| Carton contents — slats (quantity × width) | 45 meshes: 43 × 49 mm + 2 × 40 mm 50 meshes: 48 × 43 mm + 2 × 30 mm | 45 meshes: 43 × 49 mm + 2 × 40 mm 50 meshes: 48 × 49 mm + 2 × 30 mm | 45 meshes: 43 × 49 mm + 2 × 40 mm |
| Profiles included (quantity and length) | 45 meshes: upper profiles × 2 (1240 mm), lower profiles × 2 (1240 mm) 50 meshes: upper profiles × 2 (1230 mm), lower profiles × 2 (1240 mm) Aluminium profiles; | 45 meshes: 4–6 reinforcement-fold profiles (1240 mm), upper profiles × 2 (1240 mm) 50 meshes: 4–6 reinforcement-fold profiles (1240 mm), upper profiles × 2 (1230 mm) Aluminium profiles; depending on project height | 4–6 V profiles (1240 mm); upper profiles × 2 + lower profiles × 2 (1240 mm) PVC profiles; depending on project height |
| Slat thickness | 4 mm | 4 mm | 5,6 mm |
| Profile thickness | Not specified in the product sheet | Not specified in the product sheet | 0,8 mm |
| Material | Wood composite | Wood composite | High-quality PVC (Polyvinyl Chloride) |
| Installation type | Woven installation. Two weaving directions possible (see instructions) | Straight installation: factory pre-mounted inserts | Straight installation, without clips or tools (approx. 9 minutes) |
| Maintenance | Pressure washer, minimum distance 1 m | Pressure washer, minimum distance 1 m | High-pressure washer at a minimum distance of 1 m |
| Horizontal wire | 5 mm minimum | 5 mm recommended | 5 mm recommended |
| Reinforcement fold | Not specified in the product sheet | 10 cm compatible20 cm incompatibleOther dimensions not specified | 20 cm incompatibleOther dimensions not specified |
| Bottom support requirement | Not specified in the product sheet | Slats must be self-supporting, with no load at the bottom | Not specified in the product sheet |
| Panels explicitly listed |
|
|
|
| Warranty | 10 years | 10 years | 2 years |
| Colors |
|
|
|
| Available heights |
|
|
|
What to check before ordering
Check your panel specifications to determine which kits are compatible.
① Mesh
For PVC, the mesh must be 50 to 55 mm, measured from the inside edges of the wire. Check the product sheet for composite kits.
② Horizontal wire
A 5 mm horizontal wire is required or recommended depending on the kit. Refer to the selected product sheet.
③ Panel length
The PVC kit is designed for a 2.50 m panel. For composite kits, check the product sheet for the model.
④ Reinforcement folds
The required reinforcement fold depends on the kit. Panels with a 20 cm fold are not compatible with some models.
Not sure?
Share your panel reference and specifications to request technical advice before ordering.
Technical specifications
Composite Privacy Kit - Woven Installation
Installation is strongly recommended on panels with a horizontal wire of at least 5 mm. Slats must be woven on every horizontal wire.
- Up to 95% privacy
- Wind-resistant (does not flap)
- PVC-free composite designed for outdoor use (UV, frost, hail, rot-proof)
Ultimate® Privacy Kit - Straight Installation
Before selecting this kit, verify the recommended 5 mm horizontal wire, the 10 cm reinforcement fold and that slats are self-supporting with no base constraint. Compatibility cannot be assumed from the panel brand alone; 20 cm reinforcement folds are incompatible.
- Installation in under 5 minutes
- Tool-free installation thanks to factory pre-mounted inserts
- Ready-to-install carton
PVC Privacy Kit - Straight Installation
PRO MAX and PRO+ panels are documented for this kit. For any other configuration, check a length of 2,50 m, an internal mesh of 50 or 55 mm, a horizontal wire of at least 5 mm and the absence of a 20 cm reinforcing fold. Technical validation is required if any prerequisite is missing.
- High-quality PVC, anti-UV treated
- Quick installation in approx. 9 minutes, straight mounting without clips or tools
- Simple and intuitive system
Understanding privacy screening
Privacy slats dress a rigid mesh panel to create a visual screen. The welded panel must be compatible with the selected kit: material, mesh and installation method must be checked together.
How do you choose a kit?
Start by checking the panel mesh, horizontal wire and reinforcement folds. Then choose the material and installation method: woven composite, or straight composite or PVC. The product sheet remains the reference for each configuration. Discover the Ultimate® straight-installation privacy kit.
Selected for professionals
Fence contractors, installers, landscapers and building-material suppliers can compare the three kits before preparing a project. Consult the sheets and instructions, then send the panel reference and required quantities for a quote.
Guides & Resources
guides
- Fencing Privacy Solutions for Professionals: Video Guide
maintenance
- How to Maintain a Composite Screening Kit?
- What is the lifespan of a composite screening kit?
- How to Clean a Composite Privacy Screen Kit Without Damaging It?
regulations
- Is a permit required to install a fence?
- Preliminary Declaration for a Fence: When is it Mandatory?
problems
- My Privacy Screen Kit is Moving: How to Stabilize it?
- How to Replace a Composite Slat for Screening?
comparisons
- Comparison of Screening Kits: Which Material to Choose for Your Rigid Fence?
Document a solution before including it in a project
Identify the families suited to the intended use, review the available documents and submit the constraints that require verification by Paysapro.
Submit my project requirementFAQ
Check the material, mesh dimensions, horizontal wire, reinforcement folds and panel length in the product sheet for the selected kit.
No. Each kit has its own compatibility limits. Check the product specifications and request technical validation if in doubt.
Ready to equip your projects?
Get professional pricing, installation advice and support tailored to your projects.
