45-mesh panel
Panel length: 2.50 m
Internal slats ×43
Width 49 mm

External slats ×2
Width 40 mm

Reinforcement fold profiles ×4-6
Length 1240 mm

Top finishing profiles ×2
Length 1240 mm
Photo 1 of 8
Select your panel details for an initial compatibility check.
This configuration must be validated by our team before installation.
Components per 2.50 m panel

Internal slats ×43
Width 49 mm

External slats ×2
Width 40 mm

Reinforcement fold profiles ×4-6
Length 1240 mm

Top finishing profiles ×2
Length 1240 mm

Internal slats ×48
Width 49 mm

External slats ×2
Width 30 mm

Reinforcement fold profiles ×4-6
Length 1240 mm

Top finishing profiles ×2
Length 1230 mm
Ultimate® kit installation checks
| Fence height above ground | 1m03 | 1m23 | 1m53 | 1m73 | 1m93 |
|---|---|---|---|---|---|
| Embedment depth | 400 mm | 400 mm | 600 mm | 700 mm | 800 mm |
| Hole diameter | 300 mm | 300 mm | 350 mm | 350 mm | 400 mm |
Fast installation with pre-fitted inserts for a consistent finish.
The Ultimate® Straight Installation privacy kit is compatible with the leading French and European manufacturers of rigid wire panels: Dirickx, Delclo®, MRT, Betafence, Place Clôtures, Rivisa and Clotex.
A technical validation is recommended depending on the model. Please get in touch with our sales team.
Ultimate® composite kit for straight installation on rigid panels. Clips are pre-mounted on the slats and installation can be completed in under 5 minutes without tools or accessories. Finishing profiles and reinforcement fold profiles are aluminium; an anti-tamper screw system is available as an option.
Compare privacy kits for rigid fencing
To choose between Ultimate® and the woven kit, check how the slats are held in place: Ultimate® is installed straight, with self-supporting slats and no bottom constraint. A 5 mm horizontal wire is recommended; panels with a 20 cm reinforcing fold are not compatible.
Ready-to-install carton for a 2.50 m panel, available in 45- or 50-mesh configuration. Slats must be self-supporting with no constraint at the base. A 5 mm horizontal wire is strongly recommended; panels with a 20 cm reinforcement fold are not compatible.
Before selecting this kit, verify the recommended 5 mm horizontal wire, the 10 cm reinforcement fold and that slats are self-supporting with no base constraint. Compatibility cannot be assumed from the panel brand alone; 20 cm reinforcement folds are incompatible.



Ultimate® is a wood-plastic composite privacy kit with straight installation and pre-mounted metal clips. The slats remain suspended without support at the base. The woven composite kit differs in that the slats must pass over every horizontal wire in the panel. The straight-installation PVC kit uses PVC slats and is assembled without clips. These three products are therefore not interchangeable: choose the installation method and components specified for your panel, without applying dimensions or instructions from another kit.
The Ultimate® kit is documented for 2.50 m panels, in a 45- or 50-mesh configuration, with 10 cm reinforcing folds. Panels with a 20 cm reinforcing fold are incompatible. The installation instructions strongly recommend a horizontal wire of at least 5 mm. The panel brand alone is not enough to validate the complete setup: check its reference, height, length, mesh count and fold shape. If in doubt, provide these measurements and photos to have the configuration confirmed before ordering or installation.
An Ultimate® carton is for one 2.50 m panel in the selected format. The documentation specifies 43 inner slats and 2 end slats for 45 mesh, or 48 inner slats and 2 end slats for 50 mesh. The slats are 4 mm thick and have pre-mounted clips. The kit also includes 4 to 6 aluminium reinforcing-fold profiles, depending on the height, and 2 upper aluminium finishing profiles. The mesh count is not a width in millimetres: have the format and its dimensions confirmed before ordering, especially for the 50-mesh version.
The Ultimate® product sheet lists five heights: 1.03 m, 1.23 m, 1.53 m, 1.73 m and 1.93 m. The four documented combinations are:
These references do not confirm current stock. Confirm the height, 45- or 50-mesh format and colour combination when preparing your order.
The metal clip on each slat must rest on the panel’s first horizontal wire; the slat must remain suspended, with no constraint at the bottom of the panel. The instructions begin with the V-shaped aluminium profile for the upper fold, held in place with an internal slat at the centre. The profiles are then fitted into the other folds and on the other side of the panel. Place the end slats in the first and last mesh, then the internal slats, and finally the top finishing profiles. Refer to the diagrams in the Ultimate® instructions in the documentation on this page: this is not the weaving method used for the adjacent kit.
The Ultimate® clips are pre-mounted, but the instructions specify personal protective equipment, including gloves, a mask and safety glasses, as well as a utility knife. Prepare the specified equipment and first check the panel and its anchors. The assembly of the kit must not be confused with the complete installation of a fence, site preparation or adaptation of the support. The reference to quick installation does not constitute a guaranteed timeframe for your project: the time required depends on its configuration and preparation. The presence of a utility knife does not constitute authorization to shorten the slats using an undocumented method.
Have the condition and fixings of the panel, posts and anchors checked for the site configuration, particularly its exposure. The Ultimate® product sheet gives the following embedment reference values, expressed first as embedment depth and then as hole diameter:
These reference values do not, on their own, validate all soil conditions, all base plates or a given wind exposure. Have the actual support confirmed before fitting the screening.
No: the Ultimate® product sheet lists the anti-theft screw system as an option, separate from the pre-mounted clips and the profiles supplied in the box. Do not treat it as included unless this is confirmed on your order. If you want this option, have its reference and installation instructions specified before installation. The documentation reviewed does not allow us to promise that theft is impossible or to invent a method for fastening the anti-theft screws.
Before installation, store Ultimate® slats on a dry, level surface, protected from UV radiation and heat, in a well-ventilated place. The instructions state that the colour changes during the first few weeks of exposure and that variations may occur when a slat is added later. Shade differences may also persist between slats; the sample colours and brushed finish are not contractually binding. Placing a single order for the project reduces the risk of mixing several batches, but does not guarantee a perfectly uniform shade. The outdoor exposure intended after installation should not be confused with storage conditions.
The Ultimate® instructions recommend washing once a year, ideally in spring, with a pressure washer, while maintaining a minimum distance of 1 m. The slats do not require a protective treatment product, but this does not mean that cleaning is unnecessary. For surface stains, the instructions mention a ready-to-use product containing diluted bleach, without specifying a dosage here. Follow the instructions for the product used; do not use solvents, and do not apply oil, wood stain or paint. This product reference is intended for outdoor use, not indoor use.
The Ultimate® product sheet and instructions mention a 10-year warranty. The instructions require compliance with the installation requirements and state that failure to comply voids the warranty, particularly if the slats are not left suspended and free of any restraint at the bottom. This warranty period alone does not define the full scope of possible coverage: do not present it as unconditional coverage or as a promise that the colour will remain unchanged. Keep the documentation applicable to your kit and have your professional contact review any specific case against the warranty terms.